Hpssc Post Code-490 previous paper,MCQ

1. Correct spelling is

2. She is well _______ in singing and dancing.

3. Synonym of ‘Abstinence’ is

4. Antonym of ‘Stigma’ is

5. The meaning of the idiom ‘To plaugh the sands’ is

6. A cube of 4 cm side is divided into 125 small cubes. What will be the length of the side of small cube ?

7. Among five friends, A is heavier than B, C is lighter than D. B is lighter than D, but heavier than E. Who is the heaviest ?

8. In a code A is denoted by B, B by C, C by D and so on till V then FRACTIONS is denoted in the same code by

9. Mother of Q is sister of P and daughter of M. S is the daughter of P and sister of T. What is the relation of M with T ?

10. The Court of Arbitration for Sport (CAS) is headquartered in

11. The famous temple of Baba Balak Nath is situated in the district of

12. Which of the following dances is performed during New year celebration ?

13. What is the chief characteristic or speciality of ‘Nalbari Mela’ ?

14. How many princely states were merged into centrally administered Himachal Pradesh to form it a part ‘C’ state ?

15. ‘Rewalsar Lake’ is situated in which of the following districts of H.P. ?

16. ‘Banganga’ is a tributary of which one of the following rivers in H.P. ?

17. Saach Pass is situated in which of the following districts of H.P. ?

18. ‘Pajhota Agitation’ took place in which princely state of H.P. in 1942 ?

19. ‘Maharana Pratap Sagar Dam’ is the another name of

20. ‘Chhanak Chham’ is a folk dance of which region of H.P. ?

21. State Bank of India was previously known as

22. Inclusive growth as enunciated in the Eleventh Five Year Plan does not include which one of the following ?

23. Scheme of Mid-Day Meal is not connected with

24. ‘Apna Khet, Apna Kaam’ a new scheme under MGNREGA has been initiated in which state ?

25. The disease caused by asbestos is

26. The commercial crop of Northern plain is

27. Which of the following soils is the most fertile ?

28. Guru Shikhar is the highest peak of the

29. Which of the following is structurally the most stable region ?

30. Sea weeds are an important source of

31. Cardiograph is used for tracing the

32. Production of gobar gas involves

33. The cassette tape is coated with

34. The violent explosion in the stars is called

35. A copper wire cannot be used as a fuse wire because

36. Mirages can be explained by

37. The constitutional authority vested with the power of declaring castes or tribes as the Scheduled Castes or Scheduled Tribes is the

38. The National Foundation for Communal Harmony is under the administrative control of

39. Which of the following Commonwealth Summit was hosted by India ?

40. Which one of the following is not included in the state list in the Constitution of India ?

41. ‘Vande Mataram’ our national song was written by

42. Raja Ram Mohan Roy was a pioneer in

43. China attacked India in

44. The principles of Panchsheel were enunciated by

45. Who led the No Tax Campaign in 1928 ?

46. Which of the following was raised to knighthood by Lord Curzon in 1905 ?

47. In 1684, the British East India company set up a printing press in

48. When was the first unit of the Arya Samaj established ?

49. Who founded the Pala empire ?

50. The Guptas were poor in

51. Ashtadhyayi deals with

52. Ajanta cave painting depict stories of

53. The number of diodes used in an alternator are

54. The output of an alternator is controlled by

55. The number of positive plates in a battery cell is

56. The vehicle ride will be comfortable if

57. The function of stabilizer in an automobile is to decrease the tendency to

58. Shock absorber in an automobile is used to

59. Fading of brakes occurs

60. If the pedal of a hydraulic operated brake is spongy it indicates that

61. Component of wheel cylinder which seals the brake fluid is

62. Ackerman steering gear has

63. Another name for the steering link rod is

64. The term ply rating with reference to a tyre refers to the

65. The type of wheel which cannot be used with a tubeless tyre is

66. The caster angle in an automobile is

67. The function of universal joint is to allow the propeller shaft to

68. By using synchronizing device, the two involved adjacent gears have their speed

69. The speedometer is driven from the gear box shaft called

70. The component of the torque converter that drives the oil is

71. Increase of torque in a vehicle is obtained by

72. The pressure plate is held against the clutch plate by

73. Which transmission unit dis-engages the drive and provides a smooth take up of the drive ?

74. Which car engine has three cylinder ?

75. The formula for iso-octane is

76. The information supplied by the oxygen (O2) sensor to the feedback control system is about

77. The function of alternator in an automobile is to

78. The positive plates of a lead acid battery has

79. The most effective method of controlling S.I. engine exhaust emission is by

80. Traffic signs includes

81. The total weight of vehicle and load certified and registered by the registering authority as permissible for that vehicle means

82. Public service vehicle means any motor vehicle used or adapted to be used for the carriage of passengers for hire or reward and includes

83. Any motor vehicle constructed or adapted to carry more than six person excluding the driver is

84. Any motor vehicle constructed or adapted to carry out not more than six passengers excluding the driver for hire or reward is

85. Emission standards for Bharat stage IV petrol engine vehicles with regards to CO is

86. The permit granted to a motor vehicle which carries passengers for hire or reward and is engaged under a contract is called

87. The fitness in case of private vehicle is valid for

88. The age limit for obtaining the driving licence to drive transport vehicle is

89. The comfort conditioning in air conditioning are at

90. The conditioned air supplied to the room must have the capacity to take up

91. In a vapour compression system, the condition of refrigerant before passing the condenser is

92. The human body feels comfortable when the heat stored in a body is

93. During a refrigeration cycle, heat is rejected by the refrigerant in a

94. The heat transfer from a hot body to cold body is directly proportional to the surface area and difference of temperatures between the two bodies. This statement is called

95. The transfer of heat by molecular collision is known as

96. In case of liquid and gases, the heat transfer take place according to

97. Morse test is used to determine the I.P. of a

98. The ratio of the work obtained at the crank shaft in a given time to the energy supplied during the same time is called

99. The effective inhibitor of pre-ignition is

100. The ignition quality of diesel oil is expressed by

101. The loud pulsating noise heard within the cylinder of an internal combustion engine is known as

102. A super charged engine as compared to an ordinary engine

103. The combustion in compression ignition engine is

104. Reversed Joule cycle is known as

105. The efficiency of Diesel cycle increases with

106. The compression ratio is the ratio of

107. Which of the following statement is incorrect ?

108. Which of the following statement is incorrect ?

109. The mass of excess air supplied is equal to

110. Which of the following pump is generally used to pump highly viscous fluid ?

111. A hydraulic coupling belongs to the category of

112. Multi-stage centrifugal pumps are used to

113. The co-efficient of viscosity may be determined by

114. A differential manometer is used to measure

115. The pressure of liquid measured with the help of a piezometer tube is

116. The point of contra-flexure is a point where

117. The springs in brakes and clutches are used

118. Euler’s formula hold good only for

119. The stress at which the extension of the material takes place more quickly as compared to the increase in load is called

120. The ratio of static friction to dynamic friction is always

121. The ratio of static friction to dynamic friction is always

122. The point, through which the whole weight of the vehicle act, irrespective of its position is

123. Rankine Gordon formula for buckling is valid for

124. The angle of twist of shaft is

125. The condition that results in large quantities of HC emission is :

126. The process of removing the burnt gases from the engine cylinder by the fresh charge coming into the engine cylinder from the crankcase is known as

127. A three way catalytic convertor

128. The process used to improve fatigue resistance of the metal by setting up compressive stresses in its surface, is known as :

129. During hot working of metals

130. The maximum fluctuation of speed is the

131. In a multiple V-belt drive, if one of the belt is broken, then we should replace

132. When the elements of a pair are kept in contact by the action of external forces, the pair is said to be a :

133. When the nature of contact between the elements of a pair is such that it can only slide relative to the other, the pair is known as a :

134. Specific gravity of water is taken as :

135. The property of a liquid which offers resistance to the movement of one layer of a liquid over adjacent layer of liquid, is called :

136. The weight per unit volume of a liquid at a standard temperature and pressure is called

137. Load required to produce a unit deflection in a spring is called

138. Hooks law holds good up to :

139. Modulus of rigidity may be defined as the ratio of

140. Any short-circuit in the armature winding may be tested with

141. The output of an alternator is controlled by

142. The capacity of battery is determined by the number of plates per cell and

143. The most accurate timer for electronic ignition system is the

144. The primary winding of ignition coil consists of

145. Mechanical efficiency of an automobile engine usually varies in the range :

146. From the engine indicator diagram, we obtain

147. The fuel injection timing in a distributor type pump is controlled by

148. Ignition temperature of diesel fuel is about

149. The most accurate petrol injection system is the

150. The venture in the carburettor causes the

151. Lean air fuel mixture is required for :

152. An effective method of prevention of detonation is the

153. The calorific value of gasoline is about

154. The process in which hydrocarbons are decomposed into smaller hydrocarbons is called

155. Maximum oil pressure in the lubrication system is controlled by :

156. Most commonly used lubricants in automobile are the

157. Engine overheating may result due to :

158. Percentage of fuel energy lost to the cylinder walls in an automobile engine is approximately :

159. The engine require overhauling in case of

160. Maximum permissible ovality in a cylinder is usually :

161. The vibration damper on crankshaft reduces the

162. Valve overlap occurs between

163. Most commonly used valve-actuating mechanism in modern cars is :

164. On the compression stroke the rings are pressed against

165. Each time a joint is assembled, it is recommended to replace :

166. The cylinder boxes of aluminium alloy cylinder blocks are usually plated with

167. In six-cylinder engine, the power impulse occurs after ‘X’ degrees of crankshaft rotation, where ‘X’ is

168. The maximum combustion pressure in a car petrol engine is about

169. For tightening cylinder head bolts we should prefer to use :

170. The spray of water from a car washer is at a pressure of about

171. The object of air-conditioning a car is to control there in the

172. Trafficators are light signal used for

173. In modern vehicles, the headlight dimming switch is mounted on the

174. The maximum disc runout allowed on the vehicle generally

175. On suspended vacuum brakes, there is vacuum on both sides of the piston during

176. Tread distortion is least on

177. Cornering force divided by slip angle is called

178. The included angle is the sum of the

179. The coil spring in wishbone suspension is placed between the

180. The gas used in modern shock absorbers is

181. The vehicle ride will be comfortable if

182. The inner end of the axle shaft is splined to the

183. Critical whirling speed of a shaft is increased by

184. In a torque converter maximum torque multiplication occurs at

185. Two advantages of using helical gears rather than spur gears in a transmission are :

186. The maximum value of axial force at the clutch which a driver can apply while driving, without getting fatigued is

187. Cushioning springs in clutch plate are meant to reduce :

188. Co-efficient of friction for the clutch facing is approximately :

189. The most effective section against bending is

190. The frame may get distorted to a parallelogram shape due to :

191. Compared to framed construction, the frameless construction of automobiles is economical

192. Antonyms of the word ‘Infuse’ is